Jump to: navigation, search

Difference between revisions of "Getting Started with the LimeNET-Micro"

(Getting Started with LimeNET-Micro)
(Further reading)
Line 41: Line 41:
=== Further reading ===
=== Further reading ===
* [[LimeNET-Micro_v2.1_hardware_description | LimeNET-Micro v2.1 hardware description]]
* [https://www.raspberrypi.org/documentation/ Raspberry Pi documentation] - Raspberry Pi documentation database
* [[LMS7002Mr3_Calibration_Using_MCU|LMS7002M (Mask 1) Transceiver Calibration]] - LMS7002Mr3 calibration guide, using internal MCU
* [[LimeSDR Made Simple]] - Demystifying using SDR in the real world and programming a simple example with confidence, through bite sized chunks (note that not all examples will work with the Mini, e.g. those using the waveform player)
* [https://github.com/myriadrf/LMS7002M-docs/blob/master/LMS7002M_Data_Sheet_v3.1r00.pdf LMS7002M Datasheet (PDF)] - LMS7002M RF transceiver datasheet
* [https://github.com/myriadrf/LMS7002M-docs/blob/master/LMS7002M_Programming_and_Calibration_Guide_v31r05.pdf LMS7002M Programming and Calibration Guide (PDF)] - LMS7002M programming and calibration guide

Revision as of 15:06, 3 April 2019

1 Getting Started with LimeNET-Micro

1.1 Basic setup

To get LimeNET-Micro board up and running:

  • Select how the board will be powered by placing a jumper on J27 header;
  • Connect mouse and keyboard to J10 USB connectors;
  • Connect monitor cable to J19 HDMI connector;
  • Insert CM3 module into J13 socket (or CM3(L) module into J13 and uSD card into J16 slot);
  • Flash eMMC or uSD card;
  • Install LimeSuite

1.1.1 Powering the board

LimeNET-Micro board can be powered in three ways:

  • Power over Ethernet – using RJ45 connector and power sourcing equipment (PSE) such as PoE capable network switch or PoE injector. LimeNET-Micro board works with PSE supplying power in “Mode A/Endspan” as well in “Mode B/Midspan” modes;
  • DC connector - 5V power source connected to J28 power jack should be capable to provide 2A-3A current;
  • microUSB port - 5V power source connected to J15 connector should be capable to provide 2A-3A current;

Power source can be selected fitting jumper in one of the three positions on J27 header (see Figure 1):

  • A (pins 5-6) – 5V micro USB;
  • B (pins 3-4) – 5V external DC;
  • C (pins 1-2) – Power over Ethernet;

File:LimeNET-Micro 2.1 power selection .png
Figure 12. LimeNET-Micro board power selection header

1.1.2 Flashing eMMC or uSD card

To flash eMMC or uSD card with latest Raspbian image please follow these steps:

  1. Download Raspbian image file by following this [link].
  2. Choose how the board will be powered by mounting a jumper on J27 header.
  3. Mount “USB boot”(J14) and unmount "EXT USB"(J18) jumpers.
  4. Insert CM3 module into J13 socket (or CM3(L) module into J13 and uSD card into J16 slot).
  5. Flash Raspbian image by following this guide [link].
  6. Remove “USB boot”(J14) jumper and reapply power. LimeNET-Micro should now boot to newly installed Raspbian image.

1.1.3 Installing Lime Suite

After booting to the latest Raspbian image you can install LimeSuite by following the instructions on Getting Started with Lime Suite

1.2 FPGA programming

Intel MAX10 FPGA can be programmed using JTAG adapter such as Intel FPGA USB Download Cable (formerly known as Altera USB-Blaster download cable). LimeNET-Micro board has two different size and pin count JTAG headers (J4 - 10pin 0.05” pitch header and J3 - 7pin 0.1” pitch edge connector). Additional cable adapter is needed to connect download cable to LimeNET-Micro board because Intel FPGA USB Download Cable comes with 10-pin, 0.1” pitch female connector.

Figure 14. FPGA JTAG pinheaders

1.3 Further reading