LimeSDR-USB hardware description

Democratising Wireless Innovation
Jump to navigation Jump to search

LimeSDR-USB Board Key Features

The LimeSDR-USB development board provides a hardware platform for developing and prototyping high-performance and logic-intensive digital and RF designs using Altera’s Cyclone IV FPGA and Lime Microsystems transceiver.

The LimeSDR-USB has two different USB connector versions. LimeSDR-USB 1v4 is micro USB type B connector (socket) based, as shown in Figure 1. LimeSDR-USB 1v4s is a USB type A connector (plug) based, as shown in Figure 2.

Figure 1. LimeSDR-USB 1v4 – micro USB type B connector board


Figure 2. LimeSDR-USB 1v4s – USB type A connector board


LimeSDR-USB board features:

  • USB Interface
    • Cypress FX3 Super Speed USB 3rd generation controller
  • FPGA Features
    • Cyclone IV EP4CE40F23C8N device in 484-pin FPGA
    • 39’600 logic elements
    • 1134 Kbits embedded memory
    • 116 embedded 18x18 multipliers
    • 4 PLLs
  • FPGA Configuration
    • JTAG mode configuration
    • Active serial mode configuration
    • Possibility to update FPGA gateware by using FX3 (USB)
  • Memory Devices
    • 2x 1Gbit (64M x 16) DDR2 SDRAM
    • 4Mbit flash for FX3 firmware
    • 16Mbit flash for FPGA gateware
    • 2 x 128K (16K x 8) EEPROMs for LMS MCU firmware, LMS MCU data
    • 1 x 64K (8K x 8) EEPROM for FX3 data
  • Connections
    • microUSB3.0 (type B) connector or USB3.0 (type A) plug
    • Coaxial RF (U.FL) connectors
    • FPGA GPIO headers (0.05” pitch)
    • FPGA and FX3 JTAG connectors (0.05” pitch)
    • 6..12V DC power jack and pinheader
    • Fan connector (3.3V)
  • Clock System
    • 30.72MHz VCTCXO (precision: ±1 ppm initial, ±4 ppm stable).
    • Possibility to lock VCTCXO to external clock or tune VCTCXO by onboard DAC
    • Programmable clock generator for the FPGA reference clock input or LMS PLLs
  • Board Size 60mm x 100mm (2.36” x 3.94”)


LimeSDR-USB board overview

LimeSDR-USB board version 1.4 picture with highlighted major connections presented in Figure 3. There are three connector types – data and debugging (USB3.0, FPGA GPIO and JTAG), power (DC jack and external supply pinheader) and high frequency (RF and reference clock).

Figure 3. LimeSDR-USB 1v4 Development Board Connectors


Board components description listed in the Table 1 and Table 2.

Table 1. Board components
Featured Devices
Board reference Type Description
IC1 FPRF Field programmable RF transceiver, LMS7002M
IC8 FPGA Altera Cyclone IV, EP4CE40F23C8N 484-BGA
IC13 USB 3.0 microcontroller Cypress FX3 Super Speed USB 3rd generation controller, CYUSB3014
Miscellaneous devices onboard
IC9 IC Quad SPDT switch, TS3A5018PW
IC6 IC Temperature sensor, LM75
IC19 IC SPI to I²C bridge, SC18IS602BIPW (not mounted)
IC17 IC I²C port expander with 4 push-pull outputs and 4 inputs, MAX7322ATE+
Configuration, Status and Setup Components
IC9 IC Quad SPDT switch, TS3A5018PW
R51, R52, R53, R54, R56, R57, R59, R60 0 Ohm resistor FPGA (IC31) MSEL[3:0]. Default mode: Active Serial Standard configuration
R115, R116, R117 10 kOhm resistor USB3.0 microcontroller (IC13) boot configuration (PMODE0[2:0]) resistors. Default mode: SPI boot, On Failure - USB Boot
R125, R127, R128 10 kOhm resistor USB3.0 microcontroller (IC13) crystal/clock frequency selection (FSLC[2:0]) resistors. Default mode: 19.2MHz crystal
J16 JTAG chain pin header USB3.0 (IC6) microcontroller’s debugging pin header, 0.05” pitch
J17, R122 Pin header USB3.0 microcontroller boot source (Flash memory or USB), 0.05” pitch jumper or 0402 0R resistor. In normal operation jumper or resistor must be placed.
SW1 Push-button USB3.0 microcontroller reset button
J11 JTAG chain pin header FPGA programming pin header for Altera USB-Blaster download cable, 0.05” pitch
LEDS1 Red-green status LEDs User defined FPGA indication LED1 (near board edge if SMD; on the bottom if through-hole), User defined FPGA indication LED2 (farther board edge if SMD; on the top if through-hole)
LEDS2 Red-green status LEDs FX3 (USB) status indication LED (near board edge if SMD; on the bottom if through-hole), board power indication LED (farther board edge if SMD; on the top if through-hole)
General User Input/Output
J12 Pin header 8 FPGA GPIOs, 0.05” pitch
J13, J14 Pin header 3.3V fan connection pin headers, 0.1” and 0.05” pitch respectively


Table 2. Board components
Memory Devices
Board reference Type Description
IC11, IC12 DDR2 memory 1Gbit (64M x 16) DDR2 SDRAM with a 16-bit data bus
IC2, IC3 EEPROM 128K (16K x 8) EEPROM, LMS7002 MCU firmware, LMS7002M data
IC18 EEPROM 64K (8K x 8) EEPROM, connected to main I2C bus
IC10 Flash memory 16Mbit Flash for FPGA configuration
IC15 Flash memory 4Mbit Flash for FX3 firmware
Communication Ports
J15 USB3.0 connector microUSB3.0 (type B) connector or USB3.0 (type A) plug
Clock Circuitry
XO1, XO2 VCTCXO 30.72MHz voltage-controlled crystal oscillator
IC24 IC Programmable clock generator for the FPGA reference clock input and RF boards
IC23 IC ADF4002 phase detector
IC22 IC DAC for TCXO (XT4) frequency tuning
J19 U.FL connector Reference clock input
J18 U.FL connector Reference clock output
Power Supply
J20 DC input jack External 6V..12V DC power supply
J21 Pin header External 6V..12V DC power supply and main internal power rail