LimeSDR-Mini v1.1 hardware description

Democratising Wireless Innovation
Jump to navigation Jump to search

LimeSDR-Mini Board Key Features

The LimeSDR-Mini is low-cost software defined radio board. LimeSDR-Mini development board provides a hardware platform for developing and prototyping high-performance and logic-intensive digital and RF designs using Intel’s MAX 10 FPGA and Lime Microsystems transceiver.

LimeSDR-Mini v1.1


LimeSDR-Mini board features:

  • USB 3.0 controller: FTDI FT601
  • FPGA: Intel MAX 10 (10M16SAU169C8G 169-UBGA)
    • 169-pin FBGA package
    • 16 K LE
    • 549 Kb M9K Memory
    • 2368 Kb User Flash Memory
    • 1x fractional phase locked loops (PLLs)
    • 45x 18x18-bit multipliers
    • 130x general purpose input/output (GPIO)
    • Single supply
    • Flash feature
    • FPGA configuration via JTAG
  • RF transceiver: Lime Microsystems LMS7002M
  • EEPROM Memory: 2x 128Kb EEPROMs for LMS MCU firmware and FPGA data
  • FLASH Memory: 4Mb Flash memory for FPGA data
  • Temperature sensor (unpopulated)
  • General user inputs/outputs:
    • 1x Dual colour (RG) LED
    • 8x + 2x FPGA GPIO pinheader (3.3V)
  • Connections:
    • USB3.0 (type A) plug
    • Coaxial RF (SMA female) connectors
    • FPGA GPIO headers (unpopulated)
    • FPGA JTAG connector (unpopulated)
    • FAN (5V or 3.3V) connector
  • Clock system:
    • 40.00MHz onboard VCTCXO
    • Possibility to trim VCTCXO by onboard DAC
    • Reference clock input and output connectors (U.FL)
  • Board size: 69mm x 31.4mm

For more information on the following topics, refer to the respective documents:

  • FTDI FT601 USB 3.0 to FIFO Bridge datasheet [link]
  • MAX 10 FPGA device family, refer to MAX 10 Device Handbook [link]
  • LMS7002M transceiver resources [link]

Board Overview

This section contains component location description on the board. LimeSDR-Mini board picture with highlighted connectors and main components is presented in Figure 2 and Figure 3.

LimeSDR-Mini v1.1 board top connectors and main components
Figure 3 LimeSDR-Mini v1.1 board bottom connectors and main componentsc


Board components description listed in the Table 1.

Table 1. Board components
Featured Devices
Board reference Type Description
IC1 FPRF Field programmable RF transceiver, LMS7002M
IC5 FPGA Intel MAX 10 (10M16SAU169C8G 169-UBGA)
IC6 USB 3.0 microcontroller Intel MAX 10 (10M16SAU169C8G 169-UBGA)
Miscellaneous devices onboard
IC8 IC Temperature sensor, LM75
Configuration, Status and Setup Components
J3 JTAG chain connector FPGA programming pin header on the board edge for Altera USB-Blaster download cable, 0.1” pitch
J4 JTAG chain connector FPGA programming pin header for Altera USB-Blaster download cable, 0.05” pitch
LED1 or LED2 LED1 or LED2c USB3.0 microcontroller (IC13) boot configuration (PMODE0[2:0]) resistors. Default mode: SPI boot, On Failure - USB Boot
General User Input/Output
J5 Pin header 8x FPGA GPIOs, 3.3V, 0.05” pitch
J6 Pin header 2x FPGA GPIOs on the board edge, 3.3V, 0.1” pitch
J10 Pin header 5V (3.3V voltage can be chosen by resistors) fan connection pin headers, 0.1” pitch
Memory Devices
IC2 IC I²C EEPROM Memory 128Kb (16K x 8), connected to RF transceiver I2C bus
IC10 IC I²C EEPROM Memory 128Kb (16K x 8), connected to FPGA I2C bus
IC11 IC11 Quad SPI Flash Memory 4Mb (512K x 8), connected to FPGA SPI
Communication Ports
J7 USB3.0 connector USB3.0 connector
Clock Circuitry
XO1 VCTCXO 40.00 MHz Voltage Controlled Temperature Compensated Crystal Oscillatorc
IC9 IC DAC for TCXO (XT4) frequency trimming
IC7 IC7 Clock buffer
J8 U.FL connector Reference clock input
J9 U.FL connector Reference clock output
Reference clock output
IC12 IC Switching regulator (1.8V)
IC13 IC Switching regulator (3.3V)
IC14 IC Linear regulator (2.5V)

LimeSDR-Mini Board Architecture

TBD

LMS7002M Based Connectivity

TBD

USB 3.0 controller

Software controls LimeSDR-Mini board via the USB3 microcontroller (FTDI USB 3.0 to FIFO interface bridge chip FT601 [link]). The controller signals description showed below:

  • FT_D[31:0] – FTDI 32-bit data interface is connected to FPGA.
  • FT_TXEn, FT_RXFn, FT_SIWUn, FT_WRn, FT_RDn, FT_OEn, FT_BE[3:0] – FTDI interface control signals.
  • FT_CLK – FTDI interface clock. Clock from FTDI is fed to FPGA.

In the table below are listed USB3.0 controller (FTDI) pins, schematic signal name, FPGA interconnections and I/O standard.

Table 3. USB3 controller (FTDI) pins
Chip pin (IC6) Chip reference (IC6) Schematic signal name FPGA pin I/O standard I/O standard
40 DATA_0 FT_D0 A2 3.3V
41 DATA_1 FT_D1 B6 3.3V
42 DATA_2 FT_D2 B3 3.3V
43 DATA_3 FT_D3 B5 3.3V
44 DATA_4 FT_D4 A3 3.3V
45 DATA_5 FT_D5 B4 3.3V
46 DATA_6 FT_D6 E6 3.3V
47 DATA_7 FT_D7 A4 3.3V
50 DATA_8 FT_D8 B12 3.3V
51 DATA_9 FT_D9 H8 3.3V
52 DATA_10 FT_D10 E9 3.3V
53 DATA_11 FT_D11 B2 3.3V
54 DATA_12 FT_D12 D9 3.3V
55 DATA_13 FT_D13 J9 3.3V
56 DATA_14 FT_D14 A9 3.3V
57 DATA_15 FT_D15 H9 3.3V
60 DATA_16 FT_D16 A7 3.3V
61 DATA_17 FT_D17 F8 3.3V
62 DATA_18 FT_D18 A6 3.3V
63 DATA_19 FT_D19 E10 3.3V
64 DATA_20 FT_D20 A5 3.3V
65 DATA_21 FT_D21 F9 3.3V
66 DATA_22 FT_D22 E8 3.3V
67 DATA_23 FT_D23 A8 3.3V
69 DATA_24 FT_D24 K11 3.3V
70 DATA_25 FT_D25 K12 3.3V
71 DATA_26 FT_D26 J12 3.3V
72 DATA_27 FT_D27 G12 3.3V
73 DATA_28 FT_D28 L13 3.3V
74 DATA_29 FT_D29 G13 3.3V
75 DATA_30 FT_D30 J13 3.3V
76 DATA_31 FT_D31 H13 3.3V
58 CLK FT_CLK G9 3.3V
4 BE_0 FT_BE0 B11 3.3V
5 BE_1 FT_BE1 C12 3.3V
6 BE_2 FT_BE2 A12 3.3V
7 BE_3 FT_BE3 B13 3.3V
8 TXE_N FT_TXEn C13 3.3V
9 RXF_N FT_RXFn A12 3.3V
10 SIWU_N FT_SIWUn - 3.3V 10K pull up
11 WR_N FT_WRn E12 3.3V
12 RD_N FT_RDn D12 3.3V
13 OE_N FT_OEn F12 3.3V
15 RESET_N FT_RESETn L12 3.3V
16 WAKEP_N FT_WAKEUPn H10 3.3V

Indication LEDs

LimeSDR-Mini board comes with one dual colour (red and green (RG)) indication LED. This LEDs can be soldered on the top (LED1) or on the bottom (LED2). By default, LED1 is populated and LED2 is unpopulated.

Figure 5 LimeSDR-Mini indication LEDs
Figure 5 LimeSDR-Mini indication LEDs

LEDs are connected to FPGA to the same lines and their function can be changed.

Low speed interfaces

TBD

Board Temperature Control

LimeSDR-Mini has integrated temperature sensor which controls FAN to keep board in operating temperature range. FAN must be connected to J10 (0.1” pitch) connector. FAN control voltage is 5V, but it can be changed to 3.3V by resistors. Fan will be turned on if board will heat up to 55°C and FAN will be turned off if board will cool down to 45°C. By default temperature sensor is unpopulated and FAN is always on.

Figure 7 FAN control temperature hysteresis

Clock Distribution

LimeSDR-Mini board clock distribution block diagram is presented in Figure 8. LimeSDR-Mini board has onboard 40.00 MHz VCTCXO that is reference clock for LMS and FPGA PLLs.

Figure 8 LimeSDR-Mini board clock distribution block diagram

VCTCXO frequency can be tuned by using DAC (IC8). Buffered VCTCXO clock is connected to RF transceiver, FPGA. Buffered VCTCXO clock is also connected to connector J9 (REF_CLK_OUT) and can be fed to external hardware for synchronisation. VCTCXO can be disconnected from clock buffer input (remove R59 and solder R62) and external reference clock can be supplied from connector J8 (REF_CLK_IN).

Table 9. LimeSDR-Mini clock pins
Source Schematic net name I/O standard FPGA pin Description
External REF_CLK_IN External reference clock input
Board Board 2.5V (3.3V) Buffered reference clock output
Clock buffer (IC7) LMK_CLK 2.5V (3.3V) H6 Buffered reference clock output
RF transceiver (IC1) RxPLL_CLK 2.5V (3.3V) Buffered reference clock output
TxPLL_CLK 2.5V (3.3V) Buffered reference clock output
LMS_MCLK1 2.5V (3.3V) G5
LMS_FCLK1 2.5V (3.3V) L3
LMS_MCLK2 2.5V (3.3V) H4
LMS_FCLK2 2.5V (3.3V) M3
USB3.0 controller FT_CLK 3.3V G9 100 MHz

Power Distribution

LimeSDR-Mini board is powered from USB port. LimeSDR-Mini board power delivery network consists of different power rails with different voltages, filters, power sequences. LimeSDR-Mini board power distribution block diagram is presented in Figure 9.

Figure 9 LimeSDR-Mini v1.1 board power distribution block diagram