LimeSDR-PCIe v1.2 hardware description

Draft

Introduction

LimeSDR-PCIe is low-cost software defined radio board based on Lime LMS7002M Field Programmable Radio Frequency (FPRF) transceiver and Altera Cyclone IV GX PFGA, through which apps can be programmed to support any type of wireless standard, e.g. UMTS, LTE, LoRa, GPS, WiFi, Zigbee, RFID, Digital Broadcasting, Radar and many more.

Complete Development Kit Package

The LimeSDR-PCIe v1.2 board from full package showed in Figure 1.

Figure x. LimeSDR-PCIe v1.2

Development kit content:

• LimeSDR-PCIe v1.2 board
• USB stick containing following files:
  • Doc/ - Documentation files for LimeSDR-PCIe
  • Drivers/ - Windows drivers for LimeSDR-PCIe
  • Gateware/ - FPGA gateware related files for LimeSDR-PCIe v1.2
  • Gui/ - LimeSuiteGUI software and related files

LimeSDR-PCIe Board Key Features

The LimeSDR-PCIe development board provides a hardware platform for developing and prototyping high-performance and logic-intensive digital and RF designs using Altera’s Cyclone IV GX FPGA and Lime Microsystems transceiver.

LimeSDR-PCIe board features:

• RF transceiver:
  • Lime Microsystems LMS7002M
• FPGA Features
  • Cyclone IV GX (EP4CGX30CF23C7N) device in 484-pin FBGA
  • 29’440 logic elements
  • 1080 Kbits embedded memory
  • 80 embedded 18x18 multipliers
  • 4 general and 2 multipurpose PLLs
  • 4 high-speed transceivers
  • PCIe (PIPE) hard IP block
• FPGA Configuration
  • JTAG mode configuration
  • Active serial mode configuration
  • Possibility to update FPGA gateware by using PCIe interface
• Memory Devices
  • 2x 1Gbit (64M x 16) dual channel DDR2 SDRAM
  • 4Mbit flash for FPGA data
  • 64Mbit flash for FPGA gateware
  • 128Kb (16K x 8) EEPROM for LMS MCU firmware and 512Kb (64K x 8) LMS MCU data
• Connections
  • PCI Express x4 (4 lanes)
  • Coaxial RF (U.FL) connectors
  • FPGA GPIO 2x8 (3.3V) headers
  • FPGA and JTAG connector
  • DC (12V) power jack and pinheader
  • FAN (12V) connector
• Clock System
  • 30.72MHz ±250 ppb onboard VCTCXO
  • Possibility to lock VCTCXO to external clock or tune VCTCXO by onboard DAC
  • Programmable clock generator for the FPGA reference clock input or LMS PLLs
  • 100 MHz and 2x 50MHz crystal oscillators for FPGA
• Board Size 68,9mm x 136,85mm

For more information on the following topics, refer to the respective documents:

• Cyclone IV device family, refer to Cyclone IV Device Handbook [link]
• LMS7002M transceiver resources [link

LimeSDR-PCIe board overview

LimeSDR-PCIe board version 1.2 picture with highlighted major connections and components presented in Figure 1 and Figure 2. There are three connector types – data and debugging (PCIe, FPGA GPIO and JTAG), power (DC jack - optional) and high frequency (RF and reference clock). LimeSDR-PCIe board version 1.2 picture with highlighted components on top presented in Figure 1.

Figure x. LimeSDR-PCIe Development Board Top Connectors and Components

LimeSDR-PCIe board version 1.2 picture with highlighted components on bottom presented in Figure 2

Figure x. LimeSDR-PCIe Development Board Bottom Components

Board components description listed in the Table 1.

Table 1. Board components

Featured Devices
Board reference	Type	Description
IC1	FPRF	Field programmable RF transceiver LMS7002M
IC8	FPGA	Altera Cyclone IV GX (EP4CGX30CF23C7N) device in 484-pin FBGA
Miscellaneous devices onboard
IC14	IC	Temperature sensor LM75
IC4, IC5, IC6, IC7	IC	SPDT Switch
Configuration, Status and Setup Elements
J11	JTAG chain pinheader	FPGA programming pinheader for Altera USB-Blaster download cable, 0.1” pitch
LEDS1 or LED1, LED4	Red-green status LEDs	User defined FPGA indication dual colour (red – green) LEDs. LEDS1 if two TH LEDs with standoff or two SMD LEDs are populated.
LED5-LED8	Green status LEDs	User defined FPGA indication green LEDs (LED3-LED6).
LED9	Green status LEDs	Power indication
General User Input/Output
J12, J13	Pinheader	8 + 8 FPGA GPIOs, 0.05” pitch
J14	Pinheader	12V fan connection pinheader, 0.1” pitch
J18	Pinheader	12V internal power rail. Can be used to power external devices.
SW1	Switch	4 pole switch
Memory Devices
Board Reference	Type	Description
IC11, IC12	DDR2 memory	1Gbit (64M x 16) DDR2 SDRAM with a 16-bit data bus
IC2, IC3	EEPROM	128K (16K x 8) and 512K (64K x 8) EEPROMs for LMS7002 MCU firmware and data
IC15	EEPROM	128K (16K x 8) EEPROM for FPGA data
IC9, IC10	Flash memory	64Mbit Flash for FPGA configuration (only one is soldered).
Communication Ports
P1	PCIe connector	PCI Express x4 connector
Clock Circuitry
XO1, XO2	VCTCXO	Voltage Controlled, Temperature Compensated Crystal Oscillator (30.72MHz, only one is soldered).
IC20	IC	Programmable clock generator (Si5351C) for the FPGA reference clock input and RF boards
IC19	IC	Phase detector (ADF4002)
J15	U.FL connector	RF connector for reference clock output
J16	U.FL connector	RF connector for external reference clock input
IC18	IC	DAC for TCXO (XO1 or XO2) frequency tuning
Power Supply
J17	DC input jack	External 12V DC power supply (Optional)
J18	Pinheader	External 12V DC power supply and internal main power rail