ClockTamerFeaturesAndTechnicalSpecification: Difference between revisions

Democratising Wireless Innovation
Jump to navigation Jump to search
(Created page with "== Output types == ClockTamer comes with one or more of the following output types: * ''CMOS''. Single-ended output, <3V peak-to-peak. The most popular option for low output...")
 
Line 56: Line 56:
{| class="wikitable"
{| class="wikitable"
|-
|-
|&nbsp
|&nbsp;
|CMOS
|CMOS
|LVDS/LVPECL
|LVDS/LVPECL

Revision as of 14:33, 29 May 2015

Output types

ClockTamer comes with one or more of the following output types:

  • CMOS. Single-ended output, <3V peak-to-peak. The most popular option for low output frequencies (<200 MHz)
  • LVDS. Differential output, <0.5V peak-to-peak. Useful if you want to generate frequencies above 200 MHz. Requires correct termination of both ends of LVDS output; you cannot use one end and leave the other floating!
  • half-LVDS. Single-ended output, <0.5V peak-to-peak. In half-LVDS outputs only positive end (N+) is accessible to a user, while negative end (N-) is terminated with 50 Ohm resistor on the ClockTamer PCB. This output has the same frequency limitation as CMOS (<200 MHz), but has lower peak-to-peak voltage.


USRP users can use either CMOS or half-LVDS outputs, although CMOS is the default and most popular option.

ClockTamer-1.2

ClockTamer-1.2 with a single CMOS output and no GPS:

ClockTamer-1.2 with all outputs and GPS:

Specifications

Output clock temperature stability 0.28ppm in 0-70C temperature range (without GPS option)
or
50ppb with GPS option
Outputs up to 2 CMOS outputs
up to 5 LVDS outputs
(default is 1 CMOS and 0 LVDS outputs)
Output connector type U.FL
Input power voltage 3.7 - 6.0V
Input power types miniUSB (enough to power !ClockTamer with 1 or 2 outputs with or without GPS)
or
6V 2-pin connector (it has 2 connectors to connect into daisy-chain with USRP fan)
Surge protection 6V power input is protected with fast acting resetable fuse
Size 35mm x 86mm x 14mm
Control miniUSB and SPI (16-pin connector for easy connection to USRP)

Output frequencies

The output frequency can be set with 1Hz precision (this is a firmware limitation and could be fixed in later firmware versions). Tuning is possible within the following ranges:

  CMOS LVDS/LVPECL
3.75 - 94.75 MHz X X
95.20 - 113.70 MHz X X
119.00 - 142.13 MHz X X
158.67 - 189.50 MHz X X
238.00 - 284.25 MHz   X
476.00 - 568.50 MHz   X
952.00 - 1137.00 MHz   X

Schematics, PCB layout and bill of materials

Schematics

Download PDF

PCB layout (click for larger version)

Bill of materials

Download XLS

Datasheets of the most important parts:

  • Atmel ATMega (AT90USB162/AT90USB82) - (PDF)
  • Connor Winfield D75A (TCXO, 10MHz/20MHz 0.28ppm) - (PDF)
  • National Semiconductor LMX2531LQ1515E/LMX2531LQ2080E (PLL + fractional VCO) - (PDF)
  • National Semiconductor LMK01000/LMK01010 (Clock Buffer, Divider, and Distributor) - (PDF)

Phase noise

Measured for 52MHz output.

Output waveform

Measurements made by Sylvain Munaut.

USRP is modified with 51R resistor across the SMA socket on the USRP.

Measured with a 350 MHz scope and a 4GHz active probe freshly calibrated with as short a ground lead as you can make.
 
It shows a dead center 2 Vpp, low ringing, and fast enough rise time to meet the USRP clock chip input requirements.

'Measurement for ClockTamer CMOS output

Measurement for ClockTamer single-ended LVDS output




ClockTamer-1.1

Specifications

Output clock temperature stability 0.28ppm in 0-70C temperature range (without GPS option)
or
50ppb with GPS sync option
Outputs up to 2 CMOS outputs
up to 3 LVPECL/LVCMOS outputs
up to 2 LVDS outputs
(default is 1 CMOS, 0 LVPECL/LVCMOS and 0 LVDS outputs)
Output connector type U.FL
Power miniUSB
or
6V 2-pin connector (2 inputs to connect into daisy-chain with USRP fan)
Surge protection 6V power input is protected with fast acting resetable fuse
Size 35mm x 86mm x 14mm
Control miniUSB and SPI (16-pin connector for easy connection to USRP)

Output frequencies

Output frequency can be set with 1Hz precision (this is a firmware limitation and could be fixed in later firmware versions). Tuning can be done in the following ranges:

  CMOS LVDS/LVPECL
1.42 - 32.92 MHz X X
32.95 - 35.91 MHz X X
36.25 - 39.50 MHz X X
40.28 - 43.89 MHz X X
45.31 - 49.38 MHz X X
51.79 - 56.43 MHz X X
60.42 - 65.83 MHz X X
72.50 - 79.00 MHz X X
90.63 - 98.75 MHz X X
120.83 - 131.67 MHz X X

Schematics, PCB layout and bill of materials

Bill of materials

Download XLS

Schematics

These are the same as ClockTamer-1.2.

PCB layout

PCB layout has only minor changes compared ClockTamer-1.2